Tervetuloa ostoksille Lumenir verkkokauppaan!

Lumenir 25mm sälekaihdin integroidulla UK-Safiiri -säätimellä

Lumenir 25mm sälekaihdin integroidulla UK-Safiiri -säätimellä
40,50 €

Availability: Varastossa

Lumenir sälekaihtimet - UK-Safiiri -säätimellä



Lumenir-sälekaihtimet valmistetaan Suomessa tarkan laadunvalvonnan alla. Valmistuksessa käytetään vain parhaita saatavilla olevia komponentteja. Jokainen kaihdin tarkastetaan valmistuksen jälkeen korkean laadun takaamiseksi.
Sälekaihtimen mitat

Measure the height

For inside mount: Measure the HEIGHT (top-to-bottom) of the exact window frame opening in three places (left, center, right). Please provide the LARGEST of these three measurements.

For outside mount: Measure from frame to frame. we recommend to add 2" to the height for wall installation.

 

 

Obstructions may cause measurements to vary. Make sure to note them when measuring.

Important: Measure the depth of any protruding sill, ledge or molding that may interfere with the hanging of your blind. Protruding heaters, frames, locks, handles, sills etc. may interfere with your measurements. Please indicate them when measuring your window frame.

Remember: To ensure accurate measurements, use only a high quality, steel tape measure with a wide blade (minimum 1/2”). Tell your Sales Associate about any obstructions inside your window frame (locks, screens, doorknobs, handles, radiators, plants, etc.). Provide all measurements to the nearest 1/8”.

Required minimum depth: min depth needed is 1 1/2" and for full recess you need 3 1/4”

Measure the width

Measure the width side-to-side of the exact window frame opening in three places (top, middle, bottom). Please provide the smallest of these three measurements and round down to nearest 1/8 inch.

Please note that for an inside mount blind, Blinds to Go recommends a standard deduction of 3/8” (0.375”) on the dimension of the window. This standard deduction permits the blind and the brackets to be installed in the window.

 

Obstructions may cause measurements to vary. Make sure to note them when measuring.

Important: Measure the depth of any protruding sill, ledge or molding that may interfere with the hanging of your blind. Protruding heaters, frames, locks, handles, sills etc. may interfere with your measurements. Please indicate them when measuring your window frame.

Remember: To ensure accurate measurements, use only a high quality, steel tape measure with a wide blade (minimum 1/2”). Tell your Sales Associate about any obstructions inside your window frame (locks, screens, doorknobs, handles, radiators, plants, etc.). Provide all measurements to the nearest 1/8”.

Required minimum depth: Min depth needed: 1 1/2", Full recess depth: 3 1/4”

No-Hole Kaihdin

NoHole 1


Kupera puoli sisään päin
Tämä malli on normaalia sälekaihdinta pimentävämpi malli. Tässä mallissa vetonarut jää säleiden taakse piiloon kun säleet on käännetty. Tässä mallissa vetonarut ulospäin

NoHole 2


Kovera puoli sisään päin
Tämä malli on peittävämpi malli kuin NoHole 1.
Vetonarut säleissä huoneeseen päin.
-Säätötanko -Narukello -Vetonatu -Narupidike
Magneetit auttaa kaihdinta pysymään paikallaan alaslaskettuna, esim. tuuletusikkunoissa ja ovissa.

* Pakolliset kentät

Tuotekuvaus

Kuvaus

  • Kotimainen laatutuote
  • Takuu 5 vuotta
  • Toimitusaika: noin 2 viikkoa
  • Säleleveys 25mm
Arvostelut